information Related products Suppliers

o-Cresol, formaldehyde, epichlorohydrin polymer

MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK 730, Part A BILLERICA, MA 01821

EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-1 REACTIVITY- 0 US/CANADA: 800-255-3924
INT??L COLLECT: + 813-248-0585

Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 7/20/2006
REV: B
* HMIS CODE ratings are estimated by Epoxy Technology.
_____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA

PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE: APPEARANCE: Tan Paste SPECIFIC GRAVITY: NA
ODOR: Mild
_____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT %

Epoxy Cresol Novolac 29690-82-2 35-55%
Reaction product of epichlorohydrin and bisphenol A 025085-99-8 25-45%

Epoxy Cresol Novolac and Reaction product of epichlorohydrin and bisphenol A both require reporting under OSHA??s
Hazardous Communication Standards, 1910.1200.
_____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA

FLASH POINT: >200F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
_____________________________________________________________________________________________
IV. REACTIVITY DATA

STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.

CONDITIONS TO AVOID: Excessive heat.

MATERIALS TO AVOID: Strong oxidizing and reducing agents.

HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon
monoxide, and carbon dioxide.
_____________________________________________________________________________________________
The information and recommendations contained in this Material Safety Data Sheet have been compiled from
sources believed to be reliable and to represent the most reasonable current opinion on the subject when the MSDS
was prepared. No warranty, guarantee or representation is made as to the correctness or sufficiency of the
information. The user of this product must decide what safety measures are necessary to safely use this product,
either alone or in the combination with other products, and determine its environmental regulatory compliance
obligations under any applicable federal or state laws.
V. HEALTH HAZARD DATA EPO-TEK 730, Part A

EFFECTS OF OVER EXPOSURE

INGESTION: Not determined.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation.
SKIN CONTACT: Can cause dermatitis.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: Can cause dermatitis and sensitization.

EMERGENCY & FIRST AID PROCEDURES

EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
_____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
_____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION

RESPIRATORY PROTECTION: Wear an NIOSH approved respirator whenever high
level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.

VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: EPO-TEK 730, Part B BILLERICA, MA 01821

EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-1 REACTIVITY- 0 US/CANADA: 800-255-3924
INT??L COLLECT: + 813-248-0585

Carcinogen: NTP (No) IARC (No) OSHA (No) DATE REVISED: 7/20/2006
REV: B
* HMIS CODE ratings are estimated by Epoxy Technology.
_____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA

PERCENT VOLATILE: NA VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE: APPEARANCE: Tan Paste SPECIFIC GRAVITY: NA
ODOR: Mild
_____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT %

Polyamide Resin 68410231 75-100%

Polyamide Resin is the only ingredient that requires reporting via Mass RTK, under sections 311 and 312 of Sara
Title III.
_____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA

FLASH POINT: >365F
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
_____________________________________________________________________________________________
IV. REACTIVITY DATA

STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Excessive heat.
MATERIALS TO AVOID: Strong oxidizing and reducing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include
oxides of nitrogen, carbon monoxide, and carbon dioxide.
_____________________________________________________________________________________________
The information and recommendations contained in this Material Safety Data Sheet have been compiled from
sources believed to be reliable and to represent the most reasonable current opinion on the subject when the MSDS
was prepared. No warranty, guarantee or representation is made as to the correctness or sufficiency of the
information. The user of this product must decide what safety measures are necessary to safely use this product,
either alone or in the combination with other products, and determine its environmental regulatory compliance
obligations under any applicable federal or state laws.
V. HEALTH HAZARD DATA EPO-TEK 730, Part B

EFFECTS OF OVER EXPOSURE

INGESTION: May cause gastrointestinal irritation.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation, if inhaled.
SKIN CONTACT: Contains material that may cause moderate skin injury May cause
dermatitis and sensitization.
EYE CONTACT: Irritating to the eyes. Contains materials that may cause severe
eye irritation or injury.
CHRONIC EFFECTS OF OVER EXPOSURE: May cause dermatitis and sensitization.

EMERGENCY & FIRST AID PROCEDURES

EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
_____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
_____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION

RESPIRATORY PROTECTION: Wear an NIOSH approved respirator whenever high
level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.

VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
REGULATORY INFORMATION EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: EPO-TEK 730 Tel: (978) 667-3805
DATE REVISED: 7/20/2006
REV: B

SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION

This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right To Know Act of 1986 (40 CFR 372): None

1. TSCA Inventory Status

All the components of this product are listed on the TSCA Inventory.

2. RCRA Status

This product contains the following chemicals listed on the 40 CFR Part 261.33: None

3. CERCLA Status

This product contains the following chemicals listed on the 40 CFR Part 302.4: None

4. Transportation

Part A

Not Restricted

Part B

Not Restricted
______________________________________________________________________________________
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or
implied is made with respect to this information.

;