information Related products Suppliers

C.I. Pigment Black 28

MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: Epo Tek H70E-2LC, Part A BILLERICA, MA 01821
INGREDIENT CODE NUMBER: Not applicable
EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-2 REACTIVITY- 1 US/CANADA: 800-255-3924
*ANSI CODE: 2 INT??L COLLECT: + 813-248-0585

Carcinogen: NTP (No) IARC (No) OSHA (No) DATE ISSUED: 7/27/99

* HMIS and ANSI CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA

PERCENT VOLATILE: < 1 VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE: APPEARANCE: Opaque Paste SPECIFIC GRAVITY: NA
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT % TOXICITY DATA

Chromite Pigment 68186-91-4 5 See Ingredient 401004 MSDS

Chromite Pigment is the only ingredient that requires MSDS reporting per Mass. RTK.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA

FLASH POINT: NA
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA

STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.

CONDITIONS TO AVOID: Excessive heat.

MATERIALS TO AVOID: Strong oxidizing and reducing agents.

HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include carbon
monoxide, and carbon dioxide.
____________________________________________________________________________________________
To the best of our knowledge, the information contained herein is accurate. Epoxy Technology Inc., however,
assumes no liability for the accuracy or completeness of the information contained herein. Final determination of
suitability of any material is the sole responsibility of the user. All materials may present unknown health hazards and
should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the
only hazards which exist.
Epo Tek Part A's of: H70E, H70E Black, H70E-FL,
H70E-FL1, H70E-LC, H70E-1,
V. HEALTH HAZARD DATA H70E-175, H70E-2, H70E-2LC,
H70E-4, H70E-4LC, H70E-5,
EFFECTS OF OVEREXPOSURE H70F, H70S, H70S- 2LC,
H70S-LC

INGESTION: Contains Methanol - A flammable and toxic material.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation.
SKIN CONTACT: Can cause dermatitis.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: Can cause dermatitis and sensitization.
See MSDS for Methanol - Ingredient 701001.

EMERGENCY & FIRST AID PROCEDURES

EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION

RESPIRATORY PROTECTION: Wear an NIOSH approved respirator for organic
vapors whenever high level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.

VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
MATERIAL SAFETY DATA SHEET EPOXY TECHNOLOGY
14 FORTUNE DRIVE
PRODUCT NAME: Epo Tek H70E-2LC, Part B BILLERICA, MA 01821
INGREDIENT CODE NUMBER: Not applicable
EMERGENCY PHONE:
*HMIS: HEALTH- 2 FIRE-2 REACTIVITY- 1 US/CANADA: 800-255-3924
*ANSI CODE: 3,6 INT??L COLLECT: + 813-248-0585

DATE ISSUED: 7/27/99

* HMIS and ANSI CODE ratings are estimated by Epoxy Technology.
____________________________________________________________________________________________
I. IDENTIFICATION & PHYSICAL DATA

PERCENT VOLATILE: < 1 VAPOR PRESSURE: NA
BOILING POINT: NA SOLUBILITY IN WATER: Low
VAPOR DENSITY: >Air EVAPORATION RATE: APPEARANCE: Opaque Paste SPECIFIC GRAVITY: 2.3
ODOR: Mild
____________________________________________________________________________________________
II. HAZARDOUS INGREDIENTS CAS# WT % TOXICITY DATA

Acrylonitrile 107-13-1 < 200 ppm ACGIH (TLV-skin):TWA = 2ppm

Acrylonitrile is the only ingredient that require MSDS reporting per Mass. RTK. See the attached Memorandum.
____________________________________________________________________________________________
III. FIRE & EXPLOSION DATA

FLASH POINT: NA
EXTINGUISHING MEDIA: Dry chemical, foam, carbon dioxide.
UNUSUAL FIRE & EXPLOSION HAZARDS: Avoid fumes liberated by heat.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed containers.
____________________________________________________________________________________________
IV. REACTIVITY DATA

STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.

CONDITIONS TO AVOID: Excessive heat.

MATERIALS TO AVOID: Strong oxidizing and reducing agents.

HAZARDOUS DECOMPOSITION PRODUCTS: Fumes produced when heated to decomposition may include oxides
of nitrogen, carbon monoxide, and carbon dioxide.
____________________________________________________________________________________________
To the best of our knowledge, the information contained herein is accurate. Epoxy Technology Inc., however,
assumes no liability for the accuracy or completeness of the information contained herein. Final determination of
suitability of any material is the sole responsibility of the user. All materials may present unknown health hazards and
should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the
only hazards which exist.
Epo Tek Part B's of: H70E, H70E Black, H70E-FL,
H70E-FL1, H70E-LC, H70E-1,
V. HEALTH HAZARD DATA H70E-175, H70E-2, H70E-2LC,
H70E-4, H70E-4LC, H70E-5,
EFFECTS OF OVEREXPOSURE H70F, H70S, H70S- 2LC,
H70S-LC

INGESTION: Contains Methanol and Acrylonitrile, toxic materials.
INHALATION: Hot vapors can cause headaches, nausea, dizziness, and respiratory
irritation, if inhaled.
SKIN CONTACT: May cause dermatitis and skin sensitization.
EYE CONTACT: Irritating to the eyes. Can cause injury.
CHRONIC EFFECTS OF OVER EXPOSURE: May cause dermatitis and sensitization.
Acrylonitrile is a Human Suspected Carcinogen by NTP, IARC and OSHA.

EMERGENCY & FIRST AID PROCEDURES

EYE CONTACT: In case of eye contact, flush with water for at least 15 minutes.
Get medical attention immediately.
SKIN CONTACT: In case of skin contact, clean with soap and water. Do not use
solvents. Remove contaminated clothing.
INGESTION: Get medical attention immediately.
INHALATION: Remove employee to fresh air. If discomfort persists, get medical
attention.
____________________________________________________________________________________________
VI. SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS SPILLED: Eliminate ignition
sources. Use eye and skin protection. Place leaking containers in a well ventilated area.
Absorb spillage with inert material and dispose.
WASTE DISPOSAL METHOD: Incinerate or use hazardous waste treatment
procedures that are in accordance with federal, state and local regulations.
____________________________________________________________________________________________
VII. SPECIAL PROTECTION INFORMATION

RESPIRATORY PROTECTION: Wear an NIOSH approved respirator for organic
vapors whenever high level exposure to vapors or mist is anticipated.
VENTILATION: Locale exhaust recommended for exposure control.
PROTECTIVE GLOVES: Impervious gloves - neoprene or equivalent. A combination
of barrier cream and gloves is recommended.
EYE PROTECTION: Chemical splash goggles recommended.
OTHER PROTECTIVE EQUIPMENT: For operations where contact can occur, use a
face shield and impervious apron. A safety shower and eye wash facility should be
available.

VIII. SPECIAL PRECAUTIONS: Avoid contact with skin and eyes. Avoid breathing vapors. Keep containers closed
when not in use. Remove all contaminated clothing immediately and wash. Wash skin thoroughly with soap and
water after handling. Solvents should not be used to clean skin because of increased penetration potential -
protective skin oils can be dissolved by solvents.
MEMORANDUM Epo Tek Part B's of: H70E, H70E Black, H70E-FL,
H70E-FL1, H70E-LC, H70E-1,
H70E-175, H70E-2, H70E-2LC,
H70E-4, H74E-4LC, H70E-5,
H70F, H70S, H70S- 2LC,
H70S-LC

Epo Tek H70 Series employs a curing agent which is known to
contain acrylonitrile. According to OSHA, acrylonitrile is a
suspected cancer causing agent. The average acrylonitrile
content in these types of products generally range from 0.4 to
1.2 % or 4,000 to 12,000 ppm. Our proprietary vendor is
supplying us with the lowest acrylonitrile containing products
available in the US market today.

Furthermore, the convenient mix ratio ( 1 : 1 ) reduces the
acrylonitrile content of < 200 pm to a value of < 100 ppm in the mix
for safer handling. With good hygiene practices and appropriate
engineering controls, potential exposure to acrylonitrile will be minimized.
REGULATORY INFORMATION EPOXY TECHNOLOGY
14 FORTUNE DRIVE
BILLERICA, MA 01821
PRODUCT NAME: H70E-2LC TEL: (978) 667 ?? 3805
DATE ISSUED: 7/27/00

1. SARA TITLE III SECTION 313 SUPPLIER NOTIFICATION

This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the
Emergency Planning and Community Right To Know Act of 1986 (40 CFR 372): None

2. TSCA Inventory Status

All the components of this product are listed on the TSCA Inventory.

3. RCRA Status

This product contains the following chemicals listed on the 40 CFR Part 261.33: None

4. CERCLA Status

This product contains the following chemicals listed on the 40 CFR Part 302.4: None

5. Transportation

Part A

Not Restricted

Part B

Not Restricted
______________________________________________________________________________________
The information contained herein is given in good faith. However, no guarantee or warranty of any kind expressed or
implied is made with respect to this information.

;