information Related products Suppliers

Fattyacids, C9-11-branched, glycidyl esters, polymers with castor oil, formaldehyde,6-phenyl-1,3,5-triazine-2,4-diamine and phthalic anhydride

RUSTMASTERS PTY LT 39 PINE AVENUE.ULONG. NSW 2450
ph 02 66545422 fax 02 66545322 www.rustmasters.com.au dick@rustmasters.com.au

MATERIAL SAFETY DATA SHEET
RUSTMASTERS METALMASTE Issued 1 July 2006

IDENTIFICATION

Product Name METALMASTE
UN NUMBER 1263
Hazchem Code 3(Y)E
Dangerous Goods Class 3.1
Cas No N/A
Sub Risk N/A
Poisons Schedule S5 (federal)
Packaging Group 111
Packaging sizes 4 lt tins 20 lt pails

MANUFACTURERS PRODUCT CODE RMMTM

USE

Quick drying corrosion resisting paint for clean and lightly rusted steel. Single product applications, and
over Rustmasters as a tough U V stable protective system.

INGREDIENTS
CHEMICAL CAS NO UN NO PROPORTION
Phenolic Resins 67989-32-6 1263 low
White spirits 64742-82-1 1300 medium
Alkyd Resins 68459-31-4 1993 medium
Butanol 71-36-3 1120 low
Aromatic hydrocarbon 64742-95-6 1993 low
Vegetable oil 8001-79-4 none low
Vegetable oil 67989-32-6 none low
Surface active agent 64742-63-8 none low
Leaf aluminium 7429-90-5 1325 medium
Zinc Phosphate 7779-90-0 none low

Proportions Low 1%-9% Medium 10%-29%

PHYSICAL DESCRIPTION/PROPERTIES
APPEARANCE

A volatile viscous coloured liquid with a mild odour.

: -6OC (CLOSED CUP - LITERATURE VALUE)
FLASHPOINT
: 250OC
AUTO-IGNITION TEMPERATURE
: 95OC - 130OC
BOILING RANGE
VAPOUR PRESSURE : >1
MELTING POINT : NOT KNOWN
EXPLOSIVE LIMITS : LEL 1.0 UEL 3.5
VOLATILE COMPONENT : Organic solvents
SPECIFIC GRAVITY : 1.0
FORM : LIQUI

OTHER PROPERTIES
CORROSIVENESS
This product is anti corrosive (i.e. not corrosive)

OXIDISING PROPERTIES
Not applicable

REACTIVITY WITH COMMON SUBSTANCES
May react with strong acids and alkalines

ODOUR THRESHOL Very Low. Toxic components could be present without warning

HEALTH HAZARD INFORMATION

HEALTH EFFECTS - ACUTE:-

SWALLOWED;
Clear all airway passages, remove victim from area if contaminated. If unconscious apply resuscitation,do not
induce vomiting, give clear water to drink, keep victim warm. Remove all contaminated clothing; loosen tight
clothing. Seek medical aid immediately.

EYE.
Flush continuously with copious amounts of clean fresh water for fifteen minutes. Seek medical assistance if
unable to remove completely.

SKIN
Remove paint using propriety industrial cleaner, wash skin thoroughly with soap and water until no trace remains.
Remove contaminated clothing and wash before re-use. If skin irritation occurs seek medical advice.

INHALATION
Remove person from fumes as soon as possible, avoid becoming a casualty, preferably to an open shaded area.
Remove all contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable
position, making sure they are kept warm and rested. Keep at rest until fully recovered. Seek medical advice if
effect persists longer than 15 - 20 minutes.

FIRST AI Swallowed.
Lie patient on their side to allow expectoration/saliva flow. Do not induce vomiting. Give clean water only. Seek
medical attention. Relocate patient to well ventilated area.

EYE
Irrigate with copious quantities of clean fresh water for at least fifteen minutes. Seek medical assistance if irritation
persists or any residue remains.

SKIN
Wash contaminated skin with soap and water. Remove contaminated clothing and wash before re=use. If irritation
re-occurs seek medical advice.

INHALATION
Remove patient from exposure, avoid becoming a casualty yourself. Remove contaminated clothin and loosen
remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully
recovered. Seek medical assistance if effects persist.

INGESTION
Give water to ease mild irritation. DO NOT INDUCE VOMITING. Seek immediate medical assistance.

ADVICE TO DOCTORS
Treat symptomatically based on judgement of doctor and individual reactions of patient.

TOXICITY
No LD50 data available for product. Indications are that the toxicity is related to the solvent phase. They may
irritate skin, eyes and respiratory system. Inhalation of high vapour concentrations can produce central nervous
system depression, which can loss of co-ordination, impaired judgement and if exposure is prolonged,
unconsciousness and possible death.

PRECAUTIONS FOR USE

EXPOSURE STANDARDS

No value assigned for this specific material by the National Health and Medical Research Council. The TLV data
for the solvent constituents are:-
-TLV 100ppm; 525mg/m3
White Spirit
-TLV 50ppm; 250mg/m3
Solvesso
-TLV 50ppm; 790mg/m3
Butanol

TLV is the time weighed average concentration of the work atmosphere for a normal eight(8) hour work day and a
forty(40) hour work week to which nearly all workers may be repeatedly exposed day after day, without adverse
effect.

VENTILATION
Use with adequate ventilation. Vapours are heavier than air, prevent concentration in hollows and sumps. DO NOT
enter confined spaces where vapour may have collected.

ENGINEERING CONTROLS
Rustmasters MetalMaster can be applied by brush, roller, airless or conventional spray. Ensure ventilation is
adequate to maintain air concentration below exposure limits. Containers which are expanded should be treated
with extreme care. Lid can be punctured with non sparking tools to release pressure. Cover top with material before
puncturing.

Personal protection

Whilst "Metalmaster" is a low mild irritant it is advisable to take the following precautions for personal protection
and safety.
1. When handling "MetalMaster" use approved PVC/rubber gloves and wrap-around eye protection.
2. When spraying, wear dust masks and wrap-around eye protection.
Flammability:

FLAMMABLE, All potential sources of ignition (open flames, pilot lights, furnaces, and spark producing switches
and other electrical equipment) must be eliminated both in and near the work area. DO NOT SMOKE.

SAFE HANDLING INFORMATION.
Storage I Transport:

Not to be loaded with flammable gases (class 2.1) in bulk, poisonous gases (class 2.3), spontaneously
combustible substances (class 4.2) or oxidising agents (class 5). Store away from sources of heat or ignition. Keep
containers closed at all times when not in use. When used outside, store in shaded area.

Packaging I Labelling

Un Number (Resin Component): 1263
Dangerous Goods: Class 3.1
Hazchem Code: 3(Y)E
Poisons Schedule: None Allocated
Packaging Group: 111

Spills and Disposal

Spills
Shut off all possible sources of ignition. Contain, using sand or earth (excess spillage) absorbs with
sawdust, dry sand or cloth/rags. The remainder should be cleaned up with mineral thinners and the area
can then be hosed where possible to reduce tackiness/stickiness of the surface and reduce incidence of
slipping when wet. Treat small spills as for "the remainder". Whilst "MetalMaster" is not harmful to the
skin it is recommended that those persons involved in cleaning up, wear appropriate footwear
(gumboots) and rubber gloves. Remove by wiping affected skin contact areas with mild mineral thinner
or Turpentine, then wash thoroughly with soap and water until stickiness disappears. Prevent run off into
drains and waterways. Collect and seal in properly labeled drums for disposal.

Disposal
Burning is NOT recommended. Refer to State Land Waste Management Authority. Advise of flammable nature.
Normally suitable for incineration by approved authority only.

Fire and Explosion Hazard
Flammable liquid. On burning will emit poisons and noxious fumes. Keep containers cool with water spray. Fire
Fighters to wear self contained breathing apparatus if risks of exposure to vapour or product combustion exist.

ENVIRONMENTAL HAZAR
RUSTMASTERStm is a self polymerising resin system, dryers - additives, are cross linked into the structure of
polymer films therefore leaching to ground or water is of negligible order to the point of zero.

Fire Fighting Recommendations

Attack the fire from an up-wind position when possible. Use an absorbent -sand, soil or similar. USE CO2, DRY
CHEMICAL, BCF, FOAM SAND OR EARTH. DO NOT aim the extinguisher at seat of fire but attack from edge
to allow contents of fire extinguisher to "rollover" the fire and blanket the burning material. By attacking the seat
(or centre) of the fire, the extinguisher propellant can splatter the burning material over a wider area, causing minor
fire outbreaks. To drums/tins of "MetalMaster" within the vicinity of the fire, WATER SPRAY to keep contents
cool.
ADVISE THE EMERGENCY SERVICES if the fire is large, or cannot be contained by equipment or personnel
available. Fire Fighters should wear respirators of type AS 1716 if the fire is in an enclosed area.
Wrap-around safety glasses (As 1337 standards) should be worn.

OTHER INFORMATION

Contact Points
Rustmasters Pty 39 Pine Avenue phone 02 6654 5422
Ulong NSW 2450 Fax 02 6654 5322
EMERGENCYA/H 02 6652 1218 or 0417 2158 77 CONTACT Dick Booth

This information is based on DATA by Rustmasters Pty Ltd to be accurate at the time of printing, but is subject to change without notice. Information is given
in good faith but no warranty expressed or implied is made concerning it's detailed accuracy, completeness or otherwise. Independent determination as to the
suitability of the product, by the user, should be made from all sources to ensure its correct application and use. No responsibility as to its use or otherwise can
be taken once the product is out of our control. All possible assistance regarding the product is assured.

;