information Related products Suppliers

LINEAR ALKYLBENZENE A-315

MATERIAL SAFETY DATA SHEET

HITEMP-100
Inhibited & Stabilized High-Temperature
Additives Inc. Alkylate-Based Heat Transfer Fluid
5915 N. Broadway
Denver, CO 80216
Tel: 303-292-0595 Fax: 303-292-0429 MSDS No: 4000 EMERGENCY NUMBERS:
msds@additivesinc.com Ver. No: 2 PERS 800-633-8253
MSDS on-line: www.additivesinc.com Ver. Date: 1/15/02 CUSTOMER SERVICE:
303-292-0595

SECTION 1 - IDENTIFICATION
HITEMP-100
Product Name:
Inhibited and Stabilized High-Temperature Alkylate-Based Heat Transfer Fluid
Product Description:
C10 - C16 Alkybenzene derivatives
Chemical Name:
Alkylaryl Hydrocarbons
Chemical Family:
Mixture
Formula:
Inhibited Alkylate; Inhibited Alkylbenzene (C10 - C16), Heat transfer fluid, coolant
Synonyms:
68648-87-3
CAS Registry:
Not regulated
DOT Identification No.:
Not Classified as Hazardous
DOT Shipping Name:

SECTION 2 - TYPICAL COMPOSITION
MATERIAL CAS NO % WT OSHA PEL
C10 - C16 Alkylbenzene 68648-87-3 90-99% None Established
Proprietary Inhibitors Not applicable 1-10% Not Applicable

SECTION 3 - HMIS RATINGS
1
Health:
NFPA
1
Flammability:
0
Reactivity:
1
0
Special:
1 0
0
0 = minimal 1= slight 2=moderate 3= serious 4= severe

SECTION 4 ?? PHYSICAL DATA
Clear to Cloudy Colorless Liquid, mild odor
Appearance and odor:
465-475o F
Boiling Point (760 mm Hg):
1.10-1.12
Specific Gravity (water =1):
>1
Vapor Density (air =1):
<0.1
Evaporation Rate (Butyl Acetate =1):
Nil
Percent Volatiles by Volume:
100% at 20o C
Solubility in Water (% by wt):
<0,01 mmHg
Vapor Pressure (20??C):
9.0-10.0
pH:

?2002 Additives Inc. MSDS: HITEMP-100

- - - FOR DISCLAIMER OF LIABILITY SEE FINAL Not applicable
TLV and source:

May cause slight transient eye irritation, stinging or redness.
Effects of overexposure: Eyes:
Essentially nonirritating to skin. Prolonged contact may cause
Skin contact:
reddening and itchiness.
No evidence of harmful affects from available information.
Ingestion:
Inhalation: Short-term harmful health effects are not expected from vapor
generated at ambient temperature.
None known.
Systemic & Other Effects:

Flush eyes with large amounts of water for 15 minutes. If irritation
Emergency and First Aid Eye contact:
persists, get medical attention.
Procedures:
Wash off in flowing water or shower with soap and water. Wash
Skin contact:
contaminated clothing before reuse.
If the victim is fully conscious, give two glasses of water. Do Not
Ingestion:
induce vomiting. If signs or symptoms of toxicity are present, obtain
medical attention.
Remove to fresh air. If breathing has stopped, start artificial
Inhalation:
respiration. Seek medical attention.

No specific antidote. Supportive care. Treatment based on judgement of physician in
Note to Physician:
response to reactions of the patient.

SECTION 6 ?? FIRE AND EXPLOSION HAZARD DATA
Flash Point: 298-310??F
Cleveland Open Cup
Method Used:
Not Available
Flammable limits in air (% by volume):
Apply alcohol-type or all-purpose type foam for large fires. Use carbon dioxide
Extinguishing media:
or dry chemical for small fires.
Use self-contained breathing apparatus and protective clothing. Do not direct
Special Fire Fighting procedures:
a solid stream of water into hot, burning pools; this may cause frothing and
increase fire intensity.

During a fire, oxides of Nitrogen may be produced.
Unusual Fire and Explosion Hazards:

SECTION 7 ?? REACTIVITY DATA
Stability (conditions to avoid): Stable
Normally unreactive.
Incompatibility:
Oxides of carbon and nitrogen.
Hazardous decomposition products:
Will not occur.
Hazardous polymerization:

SECTION 8 ?? SPILL OR LEAK PROCEDURES
Small spills can be flushed with large amounts of water; larger spills should be
Steps to be taken if material is
collected for disposal.
released or spilled:
Salvage or burn in approved facilities in accordance with local, state and federal
Waste disposal method:
regulations.

?2002 Additives Inc. MSDS: HITEMP-100

- - - FOR DISCLAIMER OF LIABILITY SEE FINAL None needed at ambient or normal operating temperatures.
Respiratory protection:
General room ventilation is satisfactory for storage and handling at room
Ventilation:
temperature. Where exposures at elevated temperatures occur, special, local
ventilation is needed.
Polyvinyl chloride coated gloves.
Protective gloves:
Monogoggles
Eye protection:
Eye bath, safety shower.
Other protective equipment:

SECTION 10 ?? ADDITIONAL PRECAUTIONS
Avoid contact with skin, eyes and clothing. Do not take internally. Clean up
Alkaline irritant:
spills immediately.
Keep containers tightly closed when not in use. Store only in containers that
Precautions to be taken in handling
are resistant to alkaline solutions with a pH of 9.0-12.0.
and storage:

SECTION 11 ?? GENERAL COMMENTS

THE INFORMATION GIVEN HEREIN IS GIVEN IN GOOD FAITH AND FROM SOURCES WE BELIEVE RELIABLE.
BUT NO WARRANTY, EXPRESS OR IMPLIED, REGARDING ITS CORRECTNESS IS MADE.

The conditions or methods of handling, storage, use and disposal of this product are beyond our control and may be
beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for
loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of this
product.

This MSDS was prepared and is to be used only for this product. If the product is used as a component in another
product, this MSDS information may not apply.

CONSULT ADDITIVES INC. FOR FURTHER INFORMATION.

?2002 Additives Inc. MSDS: HITEMP-100

- - - FOR DISCLAIMER OF LIABILITY SEE FINAL ;