information Related products Suppliers

Poly(oxy-1,2-ethanediyl),a-sulfo-w-(nonylphenoxy)-, sodium salt(1:1)

MATERIAL SAFETY DATA SHEET
Section 1. Identification of the Substance/Preparation and of the Company/Undertaking

PRODUCT NAME: ACRYLIC POLYMER Essential Industries, Inc.
COMPANY:
P.O. Box 12
PRODUCT NUMBER: R5884
Merton, WI 53056-0012
PRODUCT USE: Acrylic copolymer

800-843-6174 PHONE NUMBER: 262-538-1122
EMERGENCY PHONE:

ABBREVIATION KEY: N.A. - Not Applicable N.E. = Not Established N.D. = Not Determined

Section 2. Composition/Information on Ingredients

CAS NO.
HAZARDOUS CHEMICAL IDENTITY % TLV-TWA (8 hours) TLV-STEL (15 mins) OSHA PEL
Ammonia salt of modified polymers 30-60 Proprietary N.E. N.E. N.D.
Water 30-60 7732-18-5 N.E. N.E. N.D.
Sodium nonylphenol ethoxylate sulfate 1-5 9014-90-8 N.E. N.E. N.D.

Section 3. Hazards Identification

ROUTES OF ENTRY: Ingestion. Eye contact. Skin contact. H.M.I.S.
POTENTIAL ACUTE HEALTH EFFECTS HAZARD RATING
HEALTH
1
Eyes: Direct contact may cause irritation.
4 = Extreme
FIRE
0 3 = High
Skin: Prolonged or repeated contact may cause irritation. 2 = Moderate
REACTIVITY
0 1 = Slight
0 = Insignificant
Ingestion: May cause gastrointestinal irritation, nausea, diarrhea. MAXIMUM PERSONAL
B PROTECTION
Inhalation: May cause respiratory tract irritation.

Section 4. First Aid Measures

FIRST AID - NOTES TO PHYSICIAN
Eyes: Flush with a large amount of water for 15 minutes holding eyelids open.
Skin: Flush skin with plenty of soap and water for at least 15 minutes while removing and isolating all contaminated clothing and shoes.

Ingestion: Give 2-3 large glasses of water. Seek medical attention.

Inhalation: Remove to fresh air.

Note to Physician: No additional information.

Section 5. Fire Fighting Measures

FLASH POINT: None.
EXTINGUISHER MEDIA: Use dry chemical or CO2.

None. N.A.
SPECIAL FIRE FIGHTING PROCEDURES: Autoignition Temperature:

UNUSUAL FIRE AND EXPLOSION HAZARDS: None. LEL: N.A. UEL: N.A.

Section 6. Environmental Precautions and Clean-up Methods

STEPS TO BE TAKEN IF MATERIALS IS SPILLED OR RELEASED:
Collect and reuse if possible. Flush to sewer with large quantities of water if permitted by regulatory authorities or absorb on inert material (sand,
clay, etc.) and place into container for proper disposal. Do not allow runoff into public waterways.

Section 7. Handling and Storage

After handling, always wash hands thoroughly with soap and water.
HANDLING REQUIREMENTS:

STORAGE REQUIREMENTS: Store in cool, dry area. Follow good housekeeping practices.
ACRYLIC POLYMER
Section 8. Exposure Controls and Personal Protection

Local Exhaust: N.A. Mechanical: N.A.
ENGINEERING CONTROLS

HYGIENIC MEASURES: Do not eat, drink or smoke during use.
PROTECTIVE CLOTHING
Protective Gloves: Rubber if needed to protect sensitive skin.
Eye Protection: Safety glasses.
Respiratory Protection: None normally required with adequate ventilation.
Protective Clothing and As needed to prevent wetting of clothing.
Equipment:

9. Physical and Chemical Properties

COLOR: Milky BOILING POINT: 100??C (212??F) <30 mm of Hg VOC: 0.05%
VAPOR PRESSURE:
ODOR: Bland FREEZING POINT: 0??C (32??F) <1 7.8 - 8.8
VAPOR DENSITY: pH:
1.05 gm/ml
Liquid N.E. Miscible
PHYSICAL STATE: EVAPORTATION RATE:
SPECIFIC SOLUBILITY:
GRAVITY:

Section 10. Stability and Reactivity

None known.
CONDITIONS TO AVOID/INCOMPATIBILITY(MATERIALS TO AVOID):
None known
HAZARDOUS TERMAL DECOMPOSITION/COMBUSTION PRODUCTS:
Stable.
STABILITY:
Will not occur.
HAZARDOUS POLYMERIZATION:

Section 11. Toxicological Information

LD50 LC50
Ingredient Name
Ammonia salt of modified polymers > 5 g/mg N.D.
Water N.D. N.D.
Sodium nonylphenol ethoxylate sulfate N.D. N.D.

DEVELOPMENT TOXICOLOGICAL DATA
NO carcinogenic effect. NO teratogenic effect.
Teratogenic Effects:
Carcinogenic Effects:
NO reproductive toxicity effect.
NO mutagenic effect. Reproductive Toxicity:
Mutagenic Effects:

Section 12. Ecological Information

Not available. ACCUMULATION: Not Available ECOTOXICITY: Not available.
MOBILITY:

The biodegrability of this product as a whole has not been deteremined; however information on the biodegrability of the
DEGRADABILITY:
ingredients contained within this product can be obtain by contacting our Regulatory Department.

Section 13. Disposal Considerations

Dispose of as permitted by all regulatory authorities.
WASTE & HANDLING INFORMATION:
Note: The waste generator must be informed of and follow all rules and regulations governing the handling and disposal of waste.

Section 14. Transport Information

TRANSPORTATION INFORMATION

DOT: IMDG: IATA:
Not Regulated.
Not Regulated. Not Regulated.
ACRYLIC POLYMER
Section 15. Regulatory Information

REGULATORY

This mixture does not contain components which are subject to the reporting requiements of Section 313 of Title III of the Superfund Amendments
and Reauthorization Act of 1986 and 40 CFR, Part 372.

Section 16. Other Information

Regulatory Affairs Department 12/13/2004.
Prepared By: Date of Preparation:
12/13/2004.
Date Printed:

;