information Related products Suppliers

Molybdenum,bis[O,O-bis(2-ethylhexyl) phosphorodithioato-kS,kS']dioxodi-m-thioxodi-,(Mo-Mo)

MATERIAL SAFETY DATA SHEET FILE NO.: B
NAME OF PRODUCT MPT?? Engine Treatment MSDS DATE: 9/24/2005
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME: MPT?? Engine Treatment
SYNONYMS: Lubricant

MANUFACTURER: MPT?? Industries
ADDRESS: 6-B Hamilton Business Park
85 Franklin Road
Dover NJ. 07801

PHONE: 973-989-9220
FAX PHONE: 973-989-9234

CHEMICAL NAME: Mixture

PRODUCT USE: Engine Oil Additive

SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS

INGREDIENT: CAS NO. % WT ACGIH-TLV-TWA
Distillates, Petroleum Hydroteated Heavy Paraffinic 64742-54-7 35-40 5mg/m3
Synthetic Hydrocarbon Base Oil 68649-12-7 10-25 None Established
Ditridecyl Adipate 16958-92-2 05-15 None Established
Molybdenum 72030-25-2 02-08 10mg/m3
Polyterafluoroethylene 9002-84-0 02-05 None Established
Petroleum Process Oil 64742-52-5 01-02 10mg/m3

SECTION 3: HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW:
Non-Hazardous under normal conditions of use.
Hot oil can cause thermal burns on contact. Spill may create a slip hazard.

ROUTES OF ENTRY:
Skin contact.

POTENTIAL HEALTH EFFECTS
EYES:
This product can cause mild eye irritation with short-term contact with liquid spray or mist.

SKIN:
This product can cause mild skin irritation with short-term exposure.

INGESTION:
If swallowed in quantities greater than one teaspoon, may cause laxative effect

INHALATION:
No adverse health effects are expected to occur upon short-term exposure

ACUTE HEALTH HAZARDS:
contains petroleum-based mineral oil. Prolonged or repeated skin contact can cause mild irritation and inflammation
characterized by drying, cracking, or oil acne. inhalation of petroleum-based mineral oil mist above applicable workplace
exposure levels can cause respiratory irritation or other pulmonary effects.

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:
May aggravate pre-existing skin disorders

SECTION 4: FIRST AID MEASURES

EYES:
Remove contact lenses if present. Flush eyes with cool, clean low-pressure water while lifting and lowering eyelids. Seek medical
attention if excessive tearing, redness, or pain persists.

SKIN:
Remove contaminated clothing. Wipe off excess material. Wash exposed skin with soap and water. Wash contaminated clothing
before reuse. Leather goods may have to be discarded. If material is injected under the skin seek medical attention immediately

MATERIAL SAFETY DATA SHEET FILE NO.: B
NAME OF PRODUCT MPT?? Engine Treatment MSDS DATE: 9/24/2005
INGESTION:
Call poison control. Unless directed by a physician do not induce vomiting or give anything to drink. Seek medical attention
immediately.

INHALATION:
This material is not expected to cause inhalation related disorders under anticipated conditions of use. In case of over-exposure
move the person to fresh air.

SECTION 5: FIRE-FIGHTING MEASURES

FLAMMABLE LIMITS IN AIR, UPPER: No Data
(% BY VOLUME) No Data LOWER: No Data

FLASH POINT:
F: 435
C: 223.9
METHOD USED: ASTM-D92

AUTOIGNITION TEMPERATURE: Not Available

NFPA HAZARD CLASSIFICATION
HEALTH: 0 FLAMMABILITY: 1 REACTIVITY: 0

HMIS HAZARD CLASSIFICATION
HEALTH: 1 FLAMMABILITY: 1 REACTIVITY: 0
PROTECTION: B

EXTINGUISHING MEDIA:
Use dry chemical, foam, carbon dioxide, or water fog

SPECIAL FIRE FIGHTING PROCEDURES:
Firefighter must use full bunker gear, including NIOSH approved positive pressure self-contained breathing apparatus.

UNUSUAL FIRE AND EXPLOSION HAZARDS:
This material can burn, but will not readily ignite. In enclosed spaces heated vapor can ignite with explosive force. Mist or spry may
burn at temperature below flash point.

HAZARDOUS DECOMPOSITION PRODUCTS:
Carbon dioxide, carbon monoxide, unburned hydrocarbons, and traces of sulfur, phosphorus, zinc, and or nitrogen.

SECTION 5 NOTES:
Combustion generates toxic fumes.

SECTION 6: ACCIDENTAL RELEASE MEASURES

ACCIDENTAL RELEASE MEASURES:
Add dry material to absorb spill. Avoid walking through material. Comply with all laws and regulations for waste disposal.

SECTION 7: HANDLING AND STORAGE

HANDLING AND STORAGE:
Avoid container damage. Keep away from excessive heat.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

VENTILATION:
None required under normal operating conditions.

RESPIRATORY PROTECTION:
None required under normal operating conditions.

EYE PROTECTION:
Safety glasses equipped with side shields should be adequate under most condition of use.

MATERIAL SAFETY DATA SHEET FILE NO.: B
NAME OF PRODUCT MPT?? Engine Treatment MSDS DATE: 9/24/2005
SKIN PROTECTION:
If prolonged contact is expected, chemical resistant gloves should be used. If product is handled at an elevated temperature, use
heat protective gloves.

WORK HYGIENIC PRACTICES:
Wash hands after using. Remove soiled clothing.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE:
Translucent Green.

ODOR:
Mild petroleum odor.

PHYSICAL STATE:
Liquid.
pH AS SUPPLIED:
pH (Other):
BOILING POINT:
F: 300
C: 148.9
MELTING POINT:
F: Not Available
C: Not Available

FREEZING POINT:
F: Not Available
C: Not Available

VAPOR PRESSURE (mmHg):
@ Nil
VAPOR DENSITY (AIR = 1):
@ Not Available

SPECIFIC GRAVITY (H2O = 1):
@ 9050

EVAPORATION RATE:
Not Available

SOLUBILITY IN WATER:
Insoluble in cold water

SECTION 10: STABILITY AND REACTIVITY

STABLE UNSTABLE

STABILITY:
Stable.

CONDITIONS TO AVOID (STABILITY):
Keep away from extreme heat, sparks or open flame and strong oxidizing conditions.

INCOMPATIBILITY (MATERIAL TO AVOID):
Strong acids, Bases and oxidizing agents

HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
Carbon dioxide, carbon monoxide, unburned hydrocarbons, and traces of sulfur, phosphorus, or nitrogen.

HAZARDOUS POLYMERIZATION:
Not expected to occur.

SECTION 11: TOXICOLOGICAL INFORMATION

TOXICOLOGICAL INFORMATION:
toxicity testing conducted on this product. Any health or toxicological information included in Sections 3 was based on data
associated with the components. Used in manufacturing this product.

MATERIAL SAFETY DATA SHEET FILE NO.: B
NAME OF PRODUCT MPT?? Engine Treatment MSDS DATE: 9/24/2005
SECTION 12: ECOLOGICAL INFORMATION

ECOLOGICAL INFORMATION:
Do not allow to enter soil, waterways, or wastewater

SECTION 13: DISPOSAL CONSIDERATIONS

WASTE DISPOSAL METHOD:
It is the responsibility of the individual using this product to follow all local, State and Federal regulation for the proper disposal of
this product and containers.

RCRA HAZARD CLASS:
It is the responsibility of the user to determine if this material is a RCRA Hazardous Waste at the time of disposal.

SECTION 14: TRANSPORT INFORMATION

U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME: Not Regulated
HAZARD CLASS: Not Regulated
ID NUMBER: Not Regulated
PACKING GROUP: Not Regulated
LABEL STATEMENT: Not Regulated

WATER TRANSPORTATION
PROPER SHIPPING NAME: Not Regulated
HAZARD CLASS: Not Regulated
ID NUMBER: Not Regulated
PACKING GROUP: Not Regulated
LABEL STATEMENTS: Not Regulated

AIR TRANSPORTATION
PROPER SHIPPING NAME: Not Regulated
HAZARD CLASS: Not Regulated
ID NUMBER:
PACKING GROUP: Not Regulated

SECTION 15: REGULATORY INFORMATION

U.S. FEDERAL REGULATIONS
TSCA (TOXIC SUBSTANCE CONTROL ACT): The components of this product are listed

SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):

311/312 HAZARD CATEGORIES: No Hazard categories identified.

STATE REGULATIONS: NJ right to know Label

SECTION 16: OTHER INFORMATION

DISCLAIMER:
Information presented herein has been compiled from source considered to be accurate and dependable to the best of our
knowledge and belief but is not guaranteed to be so. Nothing herein is to be construed as recommending any practice or any
product in violation of any law or regulation. It is the user??s responsibility to determine the suitability of any material for a specific
purpose and to adopt such safety precautions as necessary. Since conditions of use are not under our control, we must disclaim all
liability with respect to the use and disposal of our products.

;