information Related products Suppliers

Isoprene

232376 E. Pacifica Place Rancho Dominguez, CA 90220 (800) 675-1118 www.alliedhightech.com
MATERIAL/CHEMICAL SAFETY DATA SHEET
SECTION 3: HAZARDS IDENTIFICATION
SECTION 1: CHEMICAL PRODUCT & COMPANY IDENTIFICATION
Emergency Overview: Safety glasses, gloves, dust respirator are
Product Details recommended.
Aluminum Oxide
Product Name:
Hazard Statement: Not listed as a carcinogen by IARC, NTP or
Cut-Off Wheels & Wafering Blades
OSHA.
80-10000 through 80-50040
Allied Item No.:

Chemical Name: Calendered Resin/Rubber and
Resinoid Abrasive Cutting Wheels
SECTION 4: FIRST AID MEASURES
Company Identification Potential First Aid/
Health Effects Medical Info.
Allied High Tech Products, Inc.
Eye Contact: Dusts generated during Flush with large quantities
2376 East Pacifica Place
grinding may irritate eyes. of water seek medical
Rancho Dominguez, CA 90220 attention.
(310) 635-2466
Contact Point
Transportation for United States
Skin Contact: Excessive contact with Wash affected areas with
Chemtrec (800) 424-9300 * (202) 483-7616
dust may cause skin soap and water and seek
irritation. medical assistance.
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENT
Exposure Limits in Air Carcin.
Chemical Name CAS No. ACGIH TLV or TWA OSHA PEL Y/N
Products MAY contain any of the following ingredients: Inhalation: Prolonged exposure to Remove to fresh air.
Aluminum Oxide 1344-28-1 10 mg/m3 N grinding dust may cause
<95% respiratory problems or
aggravate existing
Cured Phenolic Resin NA 10 mg/m3 N conditions.
<20%
Ingestion: No known adverse No harmful effects are
Calcium Oxide 1305-78-8 2 mg/m3 N
effects. expected.
<10%

Iron Disulphide 12068-85-8 2 mg/m3 N
<20%

Note: Cutting operations may generate high noise levels. Sufficient ear
Depolymerized 78-79-5 NA N
protection should be sought if this condition exists.
Rubber <15%

Sulphur <15% 7704-34-9 10 mg/m3 N

Iron Oxide <20% 1309-38-2 5 mg/m3 N
SECTION 5: FIRE FIGHTING MEASURES
Kryolith <20% 15096-52-3 2.5 mg/m3 N Extinguishing Media: NA, will not burn.

Fire Fighting Instruction: NA

Special Hazards: NA

SECTION 6: ACCIDENTAL RELEASE MEASURES
Use normal clean-up procedures. No special precautions required.

HMIS Ratings
Ingredients are listed on the TSCA Inventory of
0
Health:
Chemical Substances.
Flammability: 0
Those not identified are non-hazardous.
Reactivity: 0
2376 E. Pacifica Place ?? Rancho Dominguez, CA 90220 ?? (800) 675-1118 ?? www.alliedhightech.com

SECTION 7: HANDLING & STORAGE SECTION 12: ECOLOGICAL INFORMATION
Handling: Avoid contact with eyes and skin. Use with adequate No information available.
ventilation. Observe good housekeeping practices.

Storage: NA

SECTION 8: EXPOSURE CONTROL & PERSONAL PROTECTION SECTION 13: DISPOSAL INFORMATION
Engineering Measures: Local exhaust system.
Landfill in accordance to Federal, State and Local
regulations.
Respiratory Protection: Use OSHA/NIOSH approved respiratory protection if level
of air contaminants is excessive.

Protective Gloves: As desired.

Eye Protection: Safety glasses or goggles with side shields.

Other: Ear protection recommended. Eyewash and safety shower are
recommended.

SECTION 9: PHYSICAL & CHEMICAL PROPERTIES SECTION 14: TRANSPORT INFORMATION
NA
Appearance: Gray, brown, reddish brown, black
Odor: May give off a rubber odor in use
Solubility: NA
Boiling Point: NA
Melting Point: NA
Flash Point: NA
Vapor Pressure: NA
Vapor Density: NA
Evaporation Rate: NA
SECTION 15: REGULATORY INFORMATION
Specific Gravity: 2.0-5.0
Flammable Limits LEL: NA NA
Flammable Limits UEL: NA

SECTION 10: STABILITY & REACTIVITY
Stability: Stable

Conditions to Avoid/Incompatibles: Overspeed and unsafe use
practices.

Decomposition Products: Dusts are generated by use. Use of
coolants may produce other decomposition products.
SECTION 16: OTHER INFORMATION
Hazardous Polymerization: Will not occur.

Legend
SECTION 11: TOXICOLOGICAL INFORMATION NAIF: No Applicable Information Found
NA: Not Available/Applicable
NA
NE: None Established
DISCLAIMER: The above information and recommendations are
believed accurate and reliable. Because it is not possible to anticipate
all conditions of use, additional safety precautions may be required.
ALLIED HIGH TECH PRODUCTS, INC. makes no warranty, either
express or implied, as to its accuracy or completeness and none is
made as to the fitness of this material for any purpose. The
manufacturer/distributor shall not be liable for damages to person or
property resulting from its use. Nothing herein shall be construed as a
recommendation for use in violation of any patent.

;