Perma-Flo
Document converted by PDFMoto freeware version
MATERIAL SAFETY DATA SHEET FILE NO.: APJC
Wel-Cote?? All-Purpose Joint Compound MSDS DATE:
07/03/02
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: Wel-Cote?? All-Purpose Joint Compound
SYNONYMS: All-Purpose, Joint Compound
PRODUCT CODES: 113, 114
MANUFACTURER: Welco Manufacturing Company
ADDRESS: 1225 Ozark Street, North Kansas City, Missouri 64116
EMERGENCY PHONE: (800)821-7352
OTHER CALLS: (816)471-1788
FAX PHONE: (816) 471-3439
CHEMICAL FAMILY: Dry mixture of minerals and binders.
CHEMICAL FORMULA: Compound
PRODUCT USE: Drywall joint finishing and repairs
PREPARED BY: Robert L. Hamilton
SECTION 1 NOTES:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT CAS Number % WT % VOL TLV (mg/m3) PEL(mg/m3)
Limestone 1317-65-3>50 >50 10 15(T)/5(R)
Mica 12001-26-2 <5 <1 3(R) 3(R)
Talc 14807-96-6 <1 <1 2(R) 2(R)
Attapulgite 12174-11-7 <1 <2 (NE) (NE)
Crystalline Silica 14808-60-7 <2 <2 0.1(R) 0.1(R)
Polysaccharide 53124-00-8
113894-92-1 <5 <5 10(T) 15(T)/5(R)
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW: Not hazardous when used according to directions.
ROUTES OF ENTRY: Eyes, Mouth, and Nose
POTENTIAL HEALTH EFFECTS
EYES: Contact can cause mechanical irritation. Rinse with water for at least 15 minutes.
SKIN: Prolonged contact may cause irritation. Wash with soap and water.
INGESTION: No known effects.
INHALATION: Inhalation of dust may irritate nose, throat, and lungs. Remove to fresh air. Seek medical attention if
condition persists.
ACUTE HEALTH HAZARDS: See above.
CHRONIC HEALTH HAZARDS: Chronic overexposure to dust may result in lung disease and/or cancer.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Pre-existing upper respiratory and lung diseases, which may
include, but are not limited to, bronchitis, emphysema, and asthma.
CARCINOGENICITY
MATERIAL NTP: IARC:
Respirable Crystalline Silica Anticipated Group 1
Document converted by PDFMoto freeware version
MATERIAL SAFETY DATA SHEET FILE NO.: APJC
Wel-Cote?? All-Purpose Joint Compound MSDS DATE:
07/03/02
SECTION 3 NOTES: When used as directed, quantities of Respirable Silica would be expected to be less than the prescribed
OSHA/NIOSH limits. Wear eye and skin protection. Use NIOSH/MSHA approved respirator when dry sanding.
SECTION 4: FIRST AID MEASURES
EYES: Rinse with water for at least 15 minutes. If redness or irritation persists, consult physician.
SKIN: Rinse with soap and water. If irritation persists, consult physician.
INGESTION: If nausea or irritation occurs, consult physician.
INHALATION: Remove to fresh air. If respiratory symptoms persist, consult physician.
NOTES TO PHYSICIANS OR FIRST AID PROVIDERS: Rinse affected areas with water.
SECTION 5: FIRE-FIGHTING MEASURES
FLAMMABLE LIMITS IN AIR, UPPER: None
LOWER: None
FLASH POINT: Non-Combustible
AUTOIGNITION TEMPERATURE: None
NFPA HAZARD CLASSIFICATION
HEALTH: 1 FLAMMABILITY: 0 REACTIVITY: 0
OTHER: N/A
HMIS HAZARD CLASSIFICATION
HEALTH: 1 FLAMMABILITY: 0 REACTIVITY: 0
PROTECTION: 0
EXTINGUISHING MEDIA: Use appropriate extinguishing media for surrounding fire.
SPECIAL FIRE FIGHTING PROCEDURES: None
UNUSUAL FIRE AND EXPLOSION HAZARDS: None
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Dioxide will be produced at temperatures exceeding 800??C. Thermal
decomposition will produce Water, Carbon Dioxide, Carbon Monoxide, and Acetic Acid.
SECTION 6: ACCIDENTAL RELEASE MEASURES
ACCIDENTAL RELEASE MEASURES: Use normal clean up procedures. Area may become slick, take caution to avoid falling. Wear
appropriate protective equipment. Shovel material into a waste container for disposal.
SECTION 6 NOTES: Dispose of material in accordance with federal, state, and local regulations.
SECTION 7: HANDLING AND STORAGE
HANDLING AND STORAGE: Use appropriate personal protection equipment when handling and finishing.
OTHER PRECAUTIONS: Do not store in extreme heat or cold. Keep out of direct sunlight.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
Document converted by PDFMoto freeware version
MATERIAL SAFETY DATA SHEET FILE NO.: APJC
Wel-Cote?? All-Purpose Joint Compound MSDS DATE:
07/03/02
ENGINEERING CONTROLS: Minimize dust exposure in accordance with good hygiene practices.
VENTILATION : Ventilate to keep exposures below TLV.
RESPIRATORY PROTECTION: Wear NIOSH/MSHA approved respirator when dry sanding.
EYE PROTECTION: Wear safety glasses or goggles to prevent particulate irritation to the eye.
SKIN PROTECTION: Generally not necessary, but may be desirable in certain conditions.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT: None
WORK HYGIENIC PRACTICES: Follow acceptable good hygiene practices.
EXPOSURE GUIDELINES: Use wet sanding technique to avoid exposure to dust.
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: White to off white powder.
ODOR: Low odor.
PHYSICAL STATE: Dry powder.
pH AS SUPPLIED: 7-8.5
BOILING POINT:
F: N/A
C: N/A
MELTING POINT: Decomposes
F: 787??
C: 1450??
FREEZING POINT:
F: N/A
C: N/A
VAPOR PRESSURE (mmHg): 0 @
F: 20??
C: -8??
SPECIFIC GRAVITY (H2O = 1): 1.5
SOLUBILITY IN WATER: Soluble
PERCENT SOLIDS BY WEIGHT: 100
PERCENT VOLATILE:
BY WT/ BY VOL @ 212??F/ 100??C
N/A N/A
VOLATILE ORGANIC COMPOUNDS (VOC): None
SECTION 10: STABILITY AND REACTIVITY
STABLE UNSTABLE
STABILITY: Yes
CONDITIONS TO AVOID (STABILITY): None known.
INCOMPATIBILITY (MATERIAL TO AVOID): None known.
Document converted by PDFMoto freeware version
MATERIAL SAFETY DATA SHEET FILE NO.: APJC
Wel-Cote?? All-Purpose Joint Compound MSDS DATE:
07/03/02
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS: Carbon Dioxide, Carbon Monoxide, and Acetic Acid.
HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID (POLYMERIZATION): None.
SECTION 11: TOXICOLOGICAL INFORMATION
TOXICOLOGICAL INFORMATION: Not toxic.
SECTION 12: ECOLOGICAL INFORMATION
ECOLOGICAL INFORMATION: No effect known.
SECTION 13: DISPOSAL CONSIDERATIONS
WASTE DISPOSAL METHOD: Dispose of in accordance with federal, state, and local regulations, as these will differ from one area to
the next.
RCRA HAZARD CLASS: None
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME: Wel-Cote? All-Purpose Joint Compound
HAZARD CLASS: Non Hazardous
ID NUMBER: NMFC 35240
PACKING GROUP: N/A
LABEL STATEMENT: None
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
TSCA (TOXIC SUBSTANCE CONTROL ACT): N/A
CERCLA (COMPREHENSIVE RESPONSE COMPENSATION, AND LIABILITY ACT): N/A
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT): N/A
311/312 HAZARD CATEGORIES: None
313 REPORTABLE INGREDIENTS: None
STATE REGULATIONS: None
INTERNATIONAL REGULATIONS: None
;
Recommended suppliers
China (Mainland)
Assessed Supplier
China Northwest Largest Factory Manufacturer Supply HYDROXYPROPYL STARCH PHOSPHATE CAS 113894-92-1
- Assay:AAAAA,
- Appearance:POWDER
- Package:1KG/Drum
- Storage:2-8°C
- Transportation:By air /Sea/ coruier
- Application:Pharm chemicals industry
Contact Supplier
China (Mainland)
Assessed Supplier
HYDROXYPROPYL STARCH PHOSPHATE CAS 113894-92-1
- Assay:Pharmaceutical grade,
- Appearance:White
- Package:In plastic outside weave or according to your request
- Storage:Sealed in dry,Room Temperature
- Transportation:We ship goods via DHL, Fedex, UPS, TNT, China post, NL Post and other couriers, weight from 10g to 1000kg or even bulker.?
- Application:Chemical raw material
Contact Supplier
China (Mainland)
Assessed Supplier
Perma-Flo
- Assay:99%
- Appearance:
- Package:drum
- Storage:
- Transportation:By Sea/Air/DHL
- Application:Henan Wentao Chemical Product Co., Ltd.
Contact Supplier
China (Mainland)
Assessed Supplier
Perma-Flo
- Assay:99.0,
- Appearance:liquid
- Package:Grams, Kilograms
- Storage:Store the container tightly closed in a dry, cool and well-ventilated place. Store apart from foodstuff containers or incompatible materials.
- Transportation:According to customer request
- Application:For R&D and commerical use
Contact Supplier
China (Mainland)
Assessed Supplier
Perma-Flo
- Assay:99%
- Appearance:powder or liquid
- Package:according to customer requirements
- Storage:store in dry dark and ventilated place
- Transportation:By Sea/Air/Courier
- Application:It is an important raw material.
Contact Supplier