Formaldehyde

1.
1.1
IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
Product identifiers
Product name
Product Number
Brand
Index-No.
CAS-No.
:
:
:
:
:
Formaldehyde solution, 36.5-38%
F8775
605-001-00-5
50-00-0
1.2
Relevant identified uses of the substance or mixture and uses advised against
Identified uses
:
Laboratory chemicals, Manufacture of substances
2.
2.1
2.2
HAZARDS IDENTIFICATION
Classification of the substance or mixture
Classification according to Regulation (EC) No 1272/2008 [EU-GHS/CLP]
Acute toxicity, Oral (Category 3)
Acute toxicity, Inhalation (Category 3)
Acute toxicity, Dermal (Category 3)
Skin corrosion (Category 1B)
Skin sensitization (Category 1)
Carcinogenicity (Category 2)
Specific target organ toxicity - single exposure (Category 1)
Specific target organ toxicity - single exposure (Category 3)
Classification according to EU Directives 67/548/EEC or 1999/45/EC
Toxic by inhalation, in contact with skin and if swallowed. Toxic: danger of very serious irreversible effects
through inhalation, in contact with skin and if swallowed. Causes burns. Limited evidence of a carcinogenic
effect. May cause sensitization by skin contact.
Label elements
Labelling according Regulation (EC) No 1272/2008 [CLP]
Pictogram
Signal word
Hazard statement(s)
H301
H311
- F8775
Danger
Toxic if swallowed.
Toxic in contact with skin.
H314
H317
H331
H335
H351
H370
Precautionary statement(s)
P260
P280
P301 + P310
P305 + P351 + P338
P310
Supplemental Hazard
Causes severe skin burns and eye damage.
May cause an allergic skin reaction.
Toxic if inhaled.
May cause respiratory irritation.
Suspected of causing cancer.
Causes damage to organs.
Do not breathe dust/ fume/ gas/ mist/ vapours/ spray.
Wear protective gloves/ protective clothing/ eye protection/ face
protection.
IF SWALLOWED: Immediately call a POISON CENTER or doctor/
physician.
IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
Immediately call a POISON CENTER or doctor/ physician.
none
Statements
According to European Directive 67/548/EEC as amended.
Hazard symbol(s)
R-phrase(s)
R23/24/25
R34
R39/23/24/25
R40
R43
S-phrase(s)
S26
S36/37/39
S45
Toxic by inhalation, in contact with skin and if swallowed.
Causes burns.
Toxic: danger of very serious irreversible effects through inhalation, in
contact with skin and if swallowed.
Limited evidence of a carcinogenic effect.
May cause sensitization by skin contact.
In case of contact with eyes, rinse immediately with plenty of water and
seek medical advice.
Wear suitable protective clothing, gloves and eye/face protection.
In case of accident or if you feel unwell, seek medical advice immediately
(show the label where possible).
2.3
3.
3.2
Other hazards
Lachrymator., Rapidly absorbed through skin.
COMPOSITION/INFORMATION ON INGREDIENTS
Mixtures
Synonyms
Formula
Molecular Weight
:
:
:
Formalin
CH2O
30,03 g/mol
Component
Formaldehyde
Classification
Concentration
CAS-No.
EC-No.
Index-No.
50-00-0
200-001-8
605-001-00-5
Acute Tox. 3; Skin Corr. 1B;
Skin Sens. 1; Carc. 2; H301 +
H311 + H331, H314, H317,
25 - 50 %
H351
T, Carc.Cat.3, R23/24/25 -
R34 - R40 - R43
Methanol
- F8775
CAS-No.
EC-No.
Index-No.
Registration number
67-56-1
200-659-6
603-001-00-X
01-2119433307-44-XXXX
Flam. Liq. 2; Acute Tox. 3;
STOT SE 1; H225, H301 +
H311 + H331, H370
F, T, R11 - R23/24/25 -
10 - 20 %
R39/23/24/25
For the full text of the H-Statements and R-Phrases mentioned in this Section, see Section 16
4.
4.1
4.2
4.3
5.
5.1
5.2
5.3
5.4
6.
6.1
6.2
6.3
6.4
7.
7.1
FIRST AID MEASURES
Description of first aid measures
General advice
Consult a physician. Show this safety data sheet to the doctor in attendance.
If inhaled
If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a physician.
In case of skin contact
Wash off with soap and plenty of water. Take victim immediately to hospital. Consult a physician.
In case of eye contact
Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.
If swallowed
Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Rinse mouth with
water. Consult a physician.
Most important symptoms and effects, both acute and delayed
Warning: contains methanol. May be fatal or cause blindness if swallowed. Cannot be made
nonpoisonous.
Indication of any immediate medical attention and special treatment needed
no data available
FIREFIGHTING MEASURES
Extinguishing media
Suitable extinguishing media
Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide.
Special hazards arising from the substance or mixture
Carbon oxides
Advice for firefighters
Wear self contained breathing apparatus for fire fighting if necessary.
Further information
Use water spray to cool unopened containers.
ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Wear respiratory protection. Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Remove
all sources of ignition. Evacuate personnel to safe areas. Beware of vapours accumulating to form
explosive concentrations. Vapours can accumulate in low areas.
Environmental precautions
Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the
environment must be avoided.
Methods and materials for containment and cleaning up
Contain spillage, and then collect with an electrically protected vacuum cleaner or by wet-brushing and
place in container for disposal according to local regulations (see section 13). Keep in suitable, closed
containers for disposal.
Reference to other sections
For disposal see section 13.
HANDLING AND STORAGE
Precautions for safe handling
Avoid contact with skin and eyes. Avoid inhalation of vapour or mist.
- F8775
Keep away from sources of ignition - No smoking.Take measures to prevent the build up of electrostatic
charge.
7.2
7.3
8.
8.1
8.2
Conditions for safe storage, including any incompatibilities
Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Containers which are
opened must be carefully resealed and kept upright to prevent leakage.
Specific end uses
no data available
EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
Components with workplace control parameters
Exposure controls
Appropriate engineering controls
Avoid contact with skin, eyes and clothing. Wash hands before breaks and immediately after handling
the product.
Personal protective equipment
Eye/face protection
Tightly fitting safety goggles. Faceshield (8-inch minimum). Use equipment for eye protection
tested and approved under appropriate government standards such as NIOSH (US) or EN
166(EU).
Skin protection
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique
(without touching glove's outer surface) to avoid skin contact with this product. Dispose of
contaminated gloves after use in accordance with applicable laws and good laboratory practices.
Wash and dry hands.
The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and
the standard EN 374 derived from it.
Immersion protection
Material: butyl-rubber
Minimum layer thickness: 0,3 mm
Break through time: > 480 min
Material tested:Butoject? ( Z677647, Size M)
Splash protection
Material: Nitrile rubber
Minimum layer thickness: 0,4 mm
Break through time: > 30 min
Material tested:Dermatril? P ( Z677388, Size M)
data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 873000, e-mail sales@kcl.de,
test method: EN374
If used in solution, or mixed with other substances, and under conditions which differ from EN 374,
contact the supplier of the CE approved gloves. This recommendation is advisory only and must
be evaluated by an Industrial Hygienist familiar with the specific situation of anticipated use by our
customers. It should not be construed as offering an approval for any specific use scenario.
Body Protection
Complete suit protecting against chemicals, The type of protective equipment must be selected
according to the concentration and amount of the dangerous substance at the specific workplace.
Respiratory protection
Where risk assessment shows air-purifying respirators are appropriate use a full-face respirator
with multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup
to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air
respirator. Use respirators and components tested and approved under appropriate government
standards such as NIOSH (US) or CEN (EU).
- F8775
9.
9.1
PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
a)
b)
c)
d)
e)
f)
g)
h)
Appearance
Odour
Odour Threshold
pH
Melting point/freezing
point
Initial boiling point and
boiling range
Flash point
Evaporation rate
Form: liquid, clear
Colour: colourless
no data available
no data available
no data available
no data available
no data available
64 °C - closed cup
no data available
i)
Flammability (solid, gas) no data available
j)
k)
l)
Upper/lower
flammability or
explosive limits
Vapour pressure
Vapour density
Upper explosion limit: 73 %(V)
Lower explosion limit: 7 %(V)
69 hPa at 37 °C
1,04 - (Air = 1.0)
m) Relative density
1,016 g/cm3
n)
o)
p)
q)
r)
s)
t)
Water solubility
Partition coefficient: n-
octanol/water
Autoignition
temperature
Decomposition
temperature
Viscosity
Explosive properties
Oxidizing properties
no data available
no data available
no data available
no data available
no data available
no data available
no data available
9.2
10.
10.1
10.2
10.3
10.4
10.5
Other safety information
no data available
STABILITY AND REACTIVITY
Reactivity
no data available
Chemical stability
no data available
Contains the following stabiliser(s):
Methanol (>=10 - <=15 %)
Possibility of hazardous reactions
no data available
Conditions to avoid
Heat, flames and sparks.
Incompatible materials
Aniline, Phenol, Isocyanates, Acid anhydrides, Strong acids, Strong bases, Strong oxidizing agents,
Amines, Peroxides
- F8775
10.6
11.
11.1
Hazardous decomposition products
Other decomposition products - no data available
TOXICOLOGICAL INFORMATION
Information on toxicological effects
Acute toxicity
no data available
Skin corrosion/irritation
no data available
Serious eye damage/eye irritation
no data available
Respiratory or skin sensitization
May cause sensitization by skin contact.
Germ cell mutagenicity
no data available
Carcinogenicity
IARC:
1 - Group 1: Carcinogenic to humans (Formaldehyde)
Reproductive toxicity
no data available
Specific target organ toxicity - single exposure
no data available
Specific target organ toxicity - repeated exposure
no data available
Aspiration hazard
no data available
Potential health effects
Inhalation
Ingestion
Skin
Eyes
Toxic if inhaled. Causes respiratory tract irritation.
Toxic if swallowed.
Toxic if absorbed through skin. Causes skin burns. May cause allergic skin
reaction.
Causes eye burns.
Signs and Symptoms of Exposure
Warning: contains methanol. May be fatal or cause blindness if swallowed. Cannot be made
nonpoisonous.
Additional Information
RTECS: LP8925000
12.
12.1
12.2
12.3
12.4
12.5
ECOLOGICAL INFORMATION
Toxicity
no data available
Persistence and degradability
no data available
Bioaccumulative potential
no data available
Mobility in soil
no data available
Results of PBT and vPvB assessment
no data available
- F8775
12.6
13.
13.1
14.
14.1
Other adverse effects
Harmful to aquatic life.
DISPOSAL CONSIDERATIONS
Waste treatment methods
Product
This combustible material may be burned in a chemical incinerator equipped with an afterburner and
scrubber. Offer surplus and non-recyclable solutions to a licensed disposal company.
Contaminated packaging
Dispose of as unused product.
TRANSPORT INFORMATION
UN number
14.2
ADR/RID: 2209
UN proper shipping name
IMDG: 2209
IATA: 2209
ADR/RID:
IMDG:
IATA:
FORMALDEHYDE SOLUTION
FORMALDEHYDE SOLUTION
Formaldehyde solution
14.3
Transport hazard class(es)
14.4
14.5
14.6
15.
ADR/RID: 8
Packaging group
ADR/RID: III
Environmental hazards
ADR/RID: no
Special precautions for user
no data available
REGULATORY INFORMATION
IMDG: 8
IMDG: III
IMDG Marine pollutant: no
IATA: 8
IATA: III
IATA: no
This safety datasheet complies with the requirements of Regulation (EC) No. 1907/2006.
15.1
15.2
16.
Safety, health and environmental regulations/legislation specific for the substance or mixture
no data available
Chemical Safety Assessment
no data available
OTHER INFORMATION
Text of H-code(s) and R-phrase(s) mentioned in Section 3
Acute Tox.
Carc.
Flam. Liq.
H225
H301 + H311 +
H331
H314
H317
H351
H370
Skin Corr.
Skin Sens.
STOT SE
F
R11
R23/24/25
R34
- F8775
Acute toxicity
Carcinogenicity
Flammable liquids
Highly flammable liquid and vapour.
Toxic if swallowed, in contact with skin or if inhaled
Causes severe skin burns and eye damage.
May cause an allergic skin reaction.
Suspected of causing cancer.
Causes damage to organs.
Skin corrosion
Skin sensitization
Specific target organ toxicity - single exposure
Highly flammable
Highly flammable.
Toxic by inhalation, in contact with skin and if swallowed.
Causes burns.
T
R39/23/24/25
R40
R43
Toxic
Toxic: danger of very serious irreversible effects through inhalation, in contact with
skin and if swallowed.
Limited evidence of a carcinogenic effect.
May cause sensitization by skin contact.
Further information
The above information is believed to be correct but does not purport to be all inclusive and
shall be used only as a guide. The information this document is based on the resent state
of our knowledge and is applicable to the product with regard to appropriate safety precautions.
It does not represent any guarantee of the properties of the product. Lookchem shall not be
held liable for any damage resulting from handling or from contact with the above product.
See reverse side of invoice or packing slip for additional terms and conditions of sale.

;

Recommended suppliers

HENAN NEW BLUE CHEMICAL CO.,LTD

China (Mainland) Assessed Supplier

Formaldehyde

  • Assay:1,
  • Appearance:colourless liquid
  • Package:25KGS/Drum
  • Storage:Room temperature
  • Transportation:BY SEA
  • Application:
Contact Supplier

Henan Wentao Chemical Product Co., Ltd.

China (Mainland) Assessed Supplier

FormaldehydeCAS NO.: 50-00-0

  • Assay:top grade ,
  • Appearance:white powder
  • Package:bag
  • Storage:Room temperature
  • Transportation:By Sea/Air/DHL
  • Application:Pharmaceutical intermediates
Contact Supplier

CHEZLYNNE TRADING (PTY) LTD

South Africa Assessed Supplier

Formaldehyde Site visiting and customize labelling accepted

  • Assay:37-41% solution
  • Appearance:
  • Package:In Liters, Drums, Big Bags and in Bulk
  • Storage:
  • Transportation:Via Sea Freight and Truck/Road
  • Application:As per the items individually
Contact Supplier

Henan Allgreen Chemical Co.,Ltd

China (Mainland) Assessed Supplier

Formaldehyde

  • Assay:98%
  • Appearance:White or off-white Solid
  • Package:According to the demand of customer
  • Storage:Sealed, dry, microtherm , avoid light and smell.
  • Transportation:by air or by sea
  • Application:Organic synthesis
Contact Supplier

Chemwill Asia Co., Ltd.

China (Mainland) Assessed Supplier

Formaldehyde CAS 50-00-0 In stock

  • Assay:1,
  • Appearance:As per COA
  • Package:export standard
  • Storage:high quality and we have in stock
  • Transportation:By AIR or by SEA
  • Application:It is an important raw material and intermediate for chemical industry.
Contact Supplier

About|Contact|Cas|Product Name|Molecular|Country|Encyclopedia

Message|New Cas|MSDS|Service|Advertisement|CAS DataBase|Article Data|Manufacturers | Chemical Catalog

©2008 LookChem.com,License: ICP

NO.:Zhejiang16009103

complaints:service@lookchem.com Desktop View