information Related products Suppliers

Rubber accelerator BZ (ZDBC)

MATERIAL SAFETY DATA SHEET
THERMO SEBS BASE COAT

Product Name: SEBS Stain Blocker / Base Coat HMIS CODES: H F R P
220G

Section I: Manufacturer Identification
Manufacturer??s Name: THERMO MANUFACTURING SYSTEMS, LLC Information Phone: (800) 882-7007
Address: 301 Walnut Springs Rd. Date Revised: 12/13/04
Lindale, TX 75771 Emergency Phone: (800) 424-9300
(CHEMTREK)

Section II: Hazardous Ingredients/SARA III Information
OCCUPATIONAL EXPOSURE LIMITS VAPOR PRESSURE WEIGHT
HAZARDOUS COMPONENTS CAS NUMBER OSHA PEL ACGH TLV OTHER: mmHG@ TEMP PERCENT
............................................................................................................................................................................................................................................................................
o
SOLVENT 64742-95-6 100PPM 100PPM N/A 2.7 68 F
STYRENE-BUTYLENE BLOCKCOPOLYMER 66070-58-4 N/A N/A N/A N/A N/A
ZINC DIBUTYLDITHIOOCARBAMATE 136-23-2 N/A N/A N/A N/A N/A
*TITANIUM DIOXIDE 13463-67-7 5 MG/M3 5 MG/M3 N/A N/A N/A 13
CALCIUM CARBONATE 1317-65-3 5 MG/M3 5 MG/M3 N/A N/A N/A
SILICON DIOXIDE (AMORPHOUS) 112945-52-5 20 MPPCF 5 MG/M3 N/A N/A N/A
MICA 12001-26-2 20 MPPCF 3 MG/M3 N/A N/A N/A

*Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372.

Section III: Physical/Chemical Characteristics
313o F to 572o F
Boiling Range: Specific Gravity (H2O=1): 1.1
Vapor Density: Heavier than air Evaporation Rate: Slower than ether
Coating V.O.C.: 3.84 lb / gal (460 g/l) Solubility in Water: Negligible
Appearance and Odor: White or colored liquid, Mild solvent odor.

Section IV: Fire and Explosion Hazard Data
14o
Flash Point:
Flammable Limits in Air By Volume: Lower: 0.5% Upper: 6.0%
Extinguishing Media: Foam, CO2, Dry Chemical and Water Fog
Method Used: PMCC

Special Fire fighting Procedures
Positive pressure self-contained breathing apparatus (scba) and structural firefighters protective clothing will provide limited protection.

Unusual Fire and Explosion Hazards
Flammable/Combustible material may be ignited by heat sparks or flames. Vapors may travel to a source of ignition and flash back. Containers
may explode in heat of fire. Vapor explosion hazard indoors, outdoors or in sewers. Runoff to sewer may create fire or explosion hazard.

Section V: Reactivity Data
Stability: Stable
Conditions to Avoid: Extreme heat, open flame.
Incompatibility: Isolate from oxidizers, heat and open flame.
Hazardous Decomposition or By-products: Fire may produce irritating or poisonous gases.
Hazardous Polymerization: WILL NOT OCCU
Section VI: Health Hazard Data
1) Inhalation Health Risks and Symptoms of Exposure: Excessive inhalation of vapors can cause nasal and respiratory irritation, dizziness, fatigue,
nausea, headache and possible unconsciousness.
2) Skin and Eye Contact Health Risks and Symptoms of Exposure: Can cause severe irritation, redness, tearing and blurred vision.
3) Skin Absorption Health Risks and Symptoms of Exposure: Skin - prolonged or repeated contact can cause moderate irritation, defatting, and
dermatitis.
4) Ingestion Health Risks and Symptoms of Exposure: Can cause gastrointestinal irritation, nausea, vomiting and diarrhea.
5) Health Hazards (Acute and Chronic): Acute - headache, dizziness, nausea, irritation. Chronic - loss of appetite, nose bleeds
6) Carcinogenicity: NTP: NO IARC Monographs: NO OSHA Regulated: NO
The information contained herein is furnished without warranty of any kind. Users should consider this data only as a supplement to other information gathered by them and must make independent determinations of
suitability and completeness of information from all sources to assure proper use and disposal of these materials and the safety and health of employees and customers. Information on this form is furnished solely for the
purpose of compliance with OSHA Hazard Communication Standard, 20CFR 1910.1200, the Workplace Hazardous Material Information System (WHMIS), and shall not be used for any other purpose.
Thermo Manufacturing Systems, LLC
CORPORATE 301 Walnut Springs Rd. Lindale, TX 75771 (800) 882-7007 (903) 881-8771 FAX (903) 881-8787
MATERIAL SAFETY DATA SHEET
THERMO SEBS BASE COAT

7) Medical Conditions Generally Aggravated by Exposure: Pre-existing eye, skin or respiratory disorders may be aggravated by exposure.
8) Emergency and First Aid Procedures: Move victim to fresh air and call emergency medical care; if not breathing, give artificial respiration; if
breathing is difficult, give oxygen. In case of contact with material, immediately flush eyes with running water for at least 15 minutes. Wash
skin with soap and water. Remove and isolate contaminated clothing and shoes at the site.

Section VII: Precautions for Safe Handling and Use
1) Steps to be taken in case material is released or spilled: SMALL LEAKS: Take up with sand or other non-combustible absorbent material and
place into containers for later disposal. LARGE LEAKS: Dike far ahead of liquid spill for later disposal. Stop leak if you can do it without
risk.
2) Waste Disposal Method: Incinerate under safe conditions or dispose of in accordance with local state and federal regulations.
3) Precautions to be taken in Handling and Storing: Do not breathe vapors, use with adequate ventilation. Do not take internally. Don??t get in
eyes. Wear impervious clothing. Keep away from heat and flame.
4) Other Precautions: Shut off ignition sources; no flames, smoking or flames in hazard area.

Section VIII: Control Measures
1) Respiratory Protection: Wear respirator in confined area.
2) Ventilation: Local Exhaust recommended.
3) Protective Gloves: Normal work gloves.
4) Eye Protection: Safety glasses or goggles.
5) Other Protective Clothing or Equipment: Eye bath and safety shower.
6) Work/Hygienic Practices: Wash hands before eating or using restrooms. Smoke only in approved areas.

Section IX: Disclaimer
Disclaimer: The information contained herein is furnished without warranty of any kind. Employers should use this information only as a
supplement to other information gathered by them and must make independent determination of suitability and completeness of information from all
sources to assure proper use of these materials and the safety and health of employees. Architectural Roof Coating assumes no responsibility for
personal injury or property damage to venders, users or third parties caused by the material.

The information contained herein is furnished without warranty of any kind. Users should consider this data only as a supplement to other information gathered by them and must make independent determinations of
suitability and completeness of information from all sources to assure proper use and disposal of these materials and the safety and health of employees and customers. Information on this form is furnished solely for the
purpose of compliance with OSHA Hazard Communication Standard, 20CFR 1910.1200, the Workplace Hazardous Material Information System (WHMIS), and shall not be used for any other purpose.
Thermo Manufacturing Systems, LLC
CORPORATE 301 Walnut Springs Rd. Lindale, TX 75771 (800) 882-7007 (903) 881-8771 FAX (903) 881-8787

;